Oklahoma City Water Heater Safety Precautions

Posted by on Dec 4, 2013 in Plumbing Contractors Oklahoma City, Water Heater Repair Oklahoma City

Effectively preserving ones water heater is vital not just so it works to its full capacity and can save some energy money, but for safety issues too. Yes, it can explode – it doesn’t happen too frequently for property owners, but obviously this is something that Water Heater Repair Oklahoma City¬†doesn’t want to have occur to you!

Vents
Venting can be kind of technical however we will review the basics below. The vent must be the exact same diameter as the draft diverter of the water heater tank. It is expected to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent must go out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some versatility in the direction they are vented.

Any roofing system or wall that the vent goes through should be a double wall. The single wall pass throughs ought to be screwed with 3 screws per area. If these fundamentals are not abided by, the vents can break down with time and carbon monoxide gas can cause major troubles within ones house. Of course we don’t want that to occur!

The only other issue with ventilation is that of backdrafting. The fumes can consume the vents with acid condensation. If plenty of this gets on cold piping and the water heater it will not be a good circumstance for an appropriately working water heater. If the fumes go back inside the instead of being appropriately vented outside, the fumes can enter the living locations of the house. Soot troubles can emerge as well.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When 2 these 2 metals are assembled in water electrolysis takes place. The process rusts one metal away to shield the other. This process is important in protecting the inside of the water heater. Assessment for leaks must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a fundamental part of the water heater, for it helps ensure the darn thing does not blow up under pressure if the temperature goes beyond the correct limits the water heater is developed for. Once a year (a minimum of) the T&P valve need to be examined to make certain, it is working effectively, for they can be susceptible to failure. Merely pulling up on the handle water should stream freely out and stop when the handle is let go of. If it simply runs or trickles, or does absolutely nothing at all, it will have to be replaced.

The drain lines for the T&P line should not be directed up, because water does not stream uphill too well. Ensure it goes down and or out please. If water is running out the drain line frequently, it is the indication of something incorrect too. It can be one of numerous different things that we will not enter below – just get in touch with a regional plumbing technician please.

Earthquake Straps
Yep, even if you do not live in an earthquake area and are required to have these on ones water heater, it is an excellent idea to do so. It appears like the majority of all new homes in sub-divisions nowadays have the water heater in the garage. Yes, there is usually a concrete curb in front of it so one does not drive a car into it, however things can mistakenly knock it over so be safe and strap that thank in.

Temperature Level Setting
It seems most domestic water heater tanks have settings of warm – hot – extremely hot … and not degree settings. Some “tips” on saving energy in the house especially in the winter season time, say to lower the setting on the tank to 120 degrees. That’s terrific for conserving energy however legionella germs, which causes Legionnaire’s condition can expand at 120 degrees. By inhaling the mist from the water in the shower, one can breathe in the microorganisms. Search for a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These normally are made of aluminum and there is absolutely nothing wrong with that in concept, though we recommend utilizing magnesium ones. Let’s say for whatever reason there is some type of emergency or disaster where one lives and one needed to utilize the water in the water heater for drinking water (since great deals of emergency preparedness people suggest doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum substances, which is bad for the human body. It is bad for the stomach, intestinal tract and joints.

The anodes help with rust defense and are important in lengthening the life of the water heater. They can also aid with odor issues with the water. Overall, magnesium anodes simply work much better for a great deal of different reasons like the health benefits, let develop of sediment, a quieter water heater, and they have a tendency to work much better with softened water.

Drain Valve
Ok, simply check it a minimum of yearly to make sure the darn thing opens and works. And it is great to drain and flush the tank at least once a year anyhow (something you obviously are doing currently). If for some reason one should utilize the water during a disaster or drain it to quite a noisy tank and have actually not drained it routinely, and it doesn’t open, it will take longer to fix the issue you are initially attempting to take care of.

Combustion Changer Hatch
Because gas and oil water heaters breathe the air sucked in from underneath, combust with it and exhale it, it is crucial to keep the area around it, specifically underneath the water heater, clean and swept. If if is not burning effectively, it can trigger preparing issues (discussed above), in addition to combustion and fume troubles and possibly be a fire hazard. A few of examining the chamber and exactly how the flame burns is objective so we are not going to enter a bunch of information right here. it is essential to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not a pretty good indication at all. One must see some blue flame at the bottom when it burns and orange and yellow at the top, however, the yellow need to not be extremely high up. One ought to see gray metal, some white condensation marks are ok.

Water Heater Repair Oklahoma City has put together an infographic to highlight the information above:

Water Heater Repair Oklahoma City